Pay more attention to us and wait for you to find out!
Manicure, a combination of UV, or phototherapy, is a product of nail polish upgrading which combines the characteristics of phototherapy (UV) products. In recent years, it has been widely used in the nail market worldwide.
The first appearance of the gum olein comes from a beautiful wish. When Nail Manicure is applied to nail polish, the most important problem for guests is the drying speed and the maintenance cycle. The two problems are just the nail polish that has been born for more than 100 years.
This new way of Manicure has the characteristics of low odor, environmental protection, health, etc. it also has the high luster and rich and colorful color that the conventional manicure oil can't match. Compared with the conventional manicure oil, it has the advantages of better durability, easy operation, more convenience and diversification in the design of manicure pattern, etc.
It is generally divided into three parts: primer, color glue (color glue) and sealing glue. Compared with traditional nail polish, it has the advantages of solvent, low stimulation, low odor, fast curing, full color, clear, easy to fall off, long cycle, and so on. At the same time, it is simple and convenient to operate, so it is very popular with manicure. With the upgrading of the products, one-step adhesive products have been launched, realizing the three in one function of primer, color adhesive and sealing adhesive. This product has been launched in the market, and there is still a lot of room for improvement. The light source of the varnish is usually cured by traditional UV lamp or LED lamp. LED lamp is characterized by no heating, no damage to the skin, faster curing, but high price. Because most of the spectrum emitted by ordinary UV lamp can not be used (such as visible light and infrared radiation), it will slightly heat up and damage the skin during curing. At the same time, low energy efficiency will lead to longer curing time than LED lamp, but it has a price advantage. The common power of common UV lamp is 36 watts, and that of LED lamp is 12 watts. With the development of Manicure market, the most popular manicure lamp is a combination of UV and LED lamps, with a common power of 36 watts.
Power comparison and curing time of various manicure lamps
Introduction to the process of nail polish coloring
Repair type A
Exfoliating Scrub
Shovel skin
Polish the nail surface
Dust removal
Upper balancing fluid (balancing fluid is the same type of product as quick drying water, nail washing gel water, etc., which is used to remove the level and grease from the nail surface), without lighting
Upper primer (apply a thin primer, which is too thick and easy to shrink or wrinkle, resulting in uneven color of nail polish; do not brush to the edge of nail, leave a distance of 0.8mm, otherwise it is easy to rise and fall off)
Base glue for lamp lighting (lighting time shall be determined according to the condition of phototherapy lamp. It doesn't matter if the surface is not dry. Don't touch it with your hand and proceed to the next step)
Apply color glue (apply a thin layer of color glue, do not brush it to the edge of the nail, leave a distance of 0.8mm, wrap the front end of the nail in, otherwise it is easy to rise and fall off)
Lighting color glue (lighting time depends on the condition of phototherapy lamp)
Repeat steps 9-10, 2-3 times (full color)
Upper sealing layer (do not brush to the edge of nail, leave a distance of 0.8mm, otherwise it is easy to rise and fall off)
Lighting seal (lighting time depends on the condition of phototherapy lamp; some seals can be applied twice)
Wash the seal layer (use nail washing cotton and some quick drying water to wash the nail gel water to wipe the nail seal layer)
Armour removal process
Nail remover (apply a little more nail remover on the nail surface with nail remover cotton)
Wrapping paper (wrap nails tightly with tin paper, do not leak, wait 15 minutes)
Degumming (use a push to remove the nail polish)
The physical property of nail polish requires that the primer has excellent adhesion to the nail, which can be maintained for 20-30 days. No yellowing, no smell, good leveling wettability, good repainting, no burning, low irritation.
Color glue (additive layer) requires good wettability, fast curing speed, no yellowing, no smell, no shrinkage, good repainting, no burning, good flexibility.
There are two types of sealing adhesive, one is scrubbing sealing layer and the other is non washing sealing layer. There is oil slick on the surface after the seal layer is cured by scrubbing. It is dry and glossy after alcohol scrubbing. Wash free sealing layer shall be dry and smooth. Both of the two sealings are required to be smooth and full, not yellowing, not scalding, smooth surface, durable luster, hot water and cold water resistance, and scratch resistance.
There are many kinds of products in domestic and foreign markets at present, but high-quality products are scarce. Some products that are not mature in technology research and development will have different problems, such as poor stability, strong smell, great stimulation, great heat release, poor scratch resistance, delamination, warping, crack, reduced gloss, discoloration, whole piece falling off, etc Elephant often appears in use.
As a resin manufacturer with advanced technology R & D capability, runao chemical has developed UV curable acrylic resin products for the system of a-gel according to customers and market demand.
Lucure8706: the main resin of color adhesive, which is two functional aliphatic polyurethane acrylate, has excellent deep curing performance, good toughness, excellent pigment wettability and yellowing resistance, and low curing heat release. 　
Fsp7043: the main resin of the primer, which is two functional modified polyester acrylate, has fast reaction speed, excellent adhesion, good flexibility, good recoat, low odor, low curing shrinkage and small heat release.
Fsp8282: the main resin of color adhesive, which is two functional aliphatic polyurethane acrylate, with fast curing speed, excellent lubricity and flexibility, good compatibility with color paste, good stability, no yellowing, low odor, low curing heat release, and non shrink adhesive.
Lucure2655: the main resin of color adhesive, which is two functional modified epoxy acrylate, has fast curing speed, excellent flexibility and certain hardness, good pigment wettability, good compatibility with color paste, good stability, low odor, low curing heat release, and high cost performance.
Fsp95937: Main resin of sealing adhesive, two functional aliphatic polyurethane acrylate, which has high gloss, good toughness, excellent chemical resistance, high smoothness, no yellowing, good scratch resistance and low heat release after curing.
For more product information, please contact customer service 15195920807 (wechat same number).
If you need to apply for a sample, please click "read the original", or reply to the sample in the official account dialogue to get the application form link.